Material:

  • Steel version, locking pin hardened: quality class 5.8
  • Stainless steel version, locking pin not hardened: threaded sleeve 1.4305 locking pin 1.4305

    Mushroom knob in anthracite gray thermoplastic

    Surface finish:

  • Steel version, locking pin hardened: black oxide finish, locking pin ground
  • Stainless steel version, locking pin not hardened: natural finish, locking pin ground

    Note:
    Indexing Plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the bolt has been manually disengaged. Style C or D is recommended for applications in which gradual disengagement of the locking bolt is desired, without any relocking of the locking pin.

    (Kipp Original Design)
  • Unit of Measure
    Items
    Indexing Plunger Short Version - Locking Pin Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Not Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Not Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Not Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Not Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Hardened - Metric

    Indexing Plunger Short Version - Locking Pin Not Hardened - Metric
    Material N/A Stainless Steel
    Style N/A A
    L N/A 29.50 mm N/A 34.50 mm N/A 41.70 mm N/A 54.00 mm N/A 61.00 mm
    D N/A 4.00 mm N/A 5.00 mm N/A 6.00 mm N/A 8.00 mm N/A 10.00 mm
    H N/A 4.00 mm N/A 5.00 mm N/A 6.00 mm N/A 8.00 mm N/A 10 mm
    D2 N/A 18.00 mm N/A 21.00 mm N/A 25.00 mm N/A 33.00 mm N/A 33.00 mm
    L2 N/A 6.00 mm N/A 7.00 mm N/A 8.00 mm N/A 10.00 mm N/A 12.00 mm
    L1 N/A 6.00 mm N/A 8.00 mm N/A 10.00 mm N/A 12.00 mm N/A 15.00 mm
    D1 N/A 5/16-24 in N/A 3/8-24 in N/A 1/2-13 in N/A 5/8-11 in N/A 3/4-10 in
    F x 30° N/A 1.00 mm N/A 1.30 mm N/A 1.80 mm N/A 2.30 mm N/A 2.80 mm
    F1 - Spring Force Initial Pressure N/A 6 N N/A 5 N N/A 6 N N/A 14 N N/A 15 N
    F2 - Spring Force Final Pressure N/A 12 N N/A 12 N N/A 14 N N/A 28 N N/A 32 N
    SW1 N/A 10.00 mm N/A 13.00 mm N/A 14.00 mm N/A 19.00 mm N/A 22.00 mm
    SW2 N/A
    End Pressure Initial-Final N/A