Indexing Plunger - No Collar - Locking Bolt Hardened

Material:

Steel version, locking pin hardened: quality class 5.8

Stainless steel version, locking pin hardened: threaded sleeve 1.4305 locking pin 1.4034

Stainless steel version, locking pin not hardened: threaded sleeve 1.4305 locking pin 1.4305

Mushroom knob in anthracite gray thermoplastic

Surface finish:

Steel version, locking pin hardened: black oxide finish, locking pin ground - Stainless steel version, locking pin hardened: natural finish, locking pin ground

Stainless steel version, locking pin not hardened: natural finish, locking pin ground

Note:
Indexing Plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the bolt has been manually disengaged. In order to screw in the Indexing Plungers, a screw-in washer can be supplied. The washer is slid beneath the disengaged mushroom knob so that the follower pins engage in the slot.

On request:
Special versions.

(Kipp Original Design)

Request Information

Unit of Measure

Items	M65588 Indexing Plunger - No Collar - Locking Bolt Hardened - Stainless Steel - Metric	M65574 Indexing Plunger - No Collar - Locking Bolt Hardened - Stainless Steel - Metric	M65576 Indexing Plunger - No Collar - Locking Bolt Hardened - Stainless Steel - Metric	M65578 Indexing Plunger - No Collar - Locking Bolt Hardened - Stainless Steel - Metric	M65580 Indexing Plunger - No Collar - Locking Bolt Hardened - Stainless Steel - Metric
Material	N/A Stainless Steel
Style	N/A G
L	N/A 32.00 mm	N/A 39.00 mm	N/A 44.00 mm	N/A 52.00 mm	N/A 68.00 mm
D	N/A 3.00 mm	N/A 4.00 mm	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm
H	N/A 3.50 mm	N/A 4.00 mm	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm
D2	N/A 14.00 mm	N/A 18.00 mm	N/A 21.00 mm	N/A 25.00 mm	N/A 33.00 mm
L2	N/A 11.00 mm	N/A 14.00 mm	N/A 15.00 mm	N/A 18.00 mm	N/A 24.00 mm
L1	N/A 17.00 mm	N/A 21.00 mm	N/A 24.00 mm	N/A 28.00 mm	N/A 36.00 mm
D1	N/A M6 X 0.75 mm	N/A M8 X 1.00 mm	N/A M10 X 1.00 mm	N/A M12 X 1.50 mm	N/A M16 X 1.50 mm
F x 30°	N/A 0.80 mm	N/A 1.30 mm	N/A 1.30 mm	N/A 1.80 mm	N/A 2.30 mm
F1 - Spring Force Initial Pressure	N/A 4.5 N	N/A 6 N	N/A 5 N	N/A 6 N	N/A 15 N
F2 - Spring Force Final Pressure	N/A 11 N	N/A 12 N	N/A 12 N	N/A 14 N	N/A 35 N
SW	N/A
End Pressure Initial-Final	N/A