Indexing Plunger with Exted Pin - No Collar

Material:

Steel version, locking pin hardened: quality class 5.8

Stainless steel version, locking pin hardened: threaded sleeve 1.4305 locking pin 1.4034

Stainless steel version, locking pin not hardened: threaded sleeve 1.4305 locking pin 1.4305

Mushroom knob in anthracite gray thermoplastic

Surface finish:

Steel version, locking pin hardened: black oxide finish, locking pin ground

Stainless steel version, locking pin hardened: natural finish, locking pin ground

Stainless steel version, locking pin not hardened: natural finish, locking pin ground

Note:
Indexing Plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the bolt has been manually disengaged. In order to screw in the locking bolts, a screw-in washer can be supplied. The washer is slid beneath the disengaged mushroom knob so that the follower pins engage in the slot.

(Kipp Original Design)

Request Information

Unit of Measure

Items	M65708 Indexing Plunger with Exted Pin - No Collar - Locking Pin Not Hardened - Stainless Steel - Metric	M65692 Indexing Plunger with Exted Pin - No Collar - Locking Pin Not Hardened - Stainless Steel - Metric	M65696 Indexing Plunger with Exted Pin - No Collar - Locking Pin Not Hardened - Stainless Steel - Metric	M65698 Indexing Plunger with Exted Pin - No Collar - Locking Pin Not Hardened - Stainless Steel - Metric	M65700 Indexing Plunger with Exted Pin - No Collar - Locking Pin Not Hardened - Stainless Steel - Metric
Material	N/A Stainless Steel
Style	N/A G
L	N/A 33.00 mm	N/A 41.00 mm	N/A 47.00 mm	N/A 55.00 mm	N/A 72.00 mm
D	N/A 3.00 mm	N/A 4.00 mm	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm
H	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm	N/A 9 mm	N/A 12 mm
D2	N/A 14.00 mm	N/A 18.00 mm	N/A 21.00 mm	N/A 25.00 mm	N/A 33.00 mm
L2	N/A 11.00 mm	N/A 14.00 mm	N/A 15.00 mm	N/A 18.00 mm	N/A 24.00 mm
L1	N/A 17.00 mm	N/A 21.00 mm	N/A 24.00 mm	N/A 28.00 mm	N/A 36.00 mm
D1	N/A M6 X 0.75 mm	N/A M8 X 1.00 mm	N/A M10 X 1.00 mm	N/A M12 X 1.50 mm	N/A M16 X 1.50 mm
F x 30°	N/A 0.80 mm	N/A 1.00 mm	N/A 1.30 mm	N/A 1.80 mm	N/A 2.30 mm
F1 - Spring Force Initial Pressure	N/A 4.5 N	N/A 6 N	N/A 5 N	N/A 6 N	N/A 15 N
F2 - Spring Force Final Pressure	N/A 11 N	N/A 15 N	N/A 16 N	N/A 18 N	N/A 45 N
SW	N/A
End Pressure Initial-Final	N/A