Indexing Plunger - No Collar - Locking Bolt Not Hardened

Material:

Steel version, locking pin hardened: quality class 5.8

Stainless steel version, locking pin hardened: threaded sleeve 1.4305 locking pin 1.4034

Stainless steel version, locking pin not hardened: threaded sleeve 1.4305 locking pin 1.4305

Mushroom knob in anthracite gray thermoplastic

Surface finish:

Steel version, locking pin hardened: black oxide finish, locking pin ground - Stainless steel version, locking pin hardened: natural finish, locking pin ground

Stainless steel version, locking pin not hardened: natural finish, locking pin ground

Note:
Indexing Plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the bolt has been manually disengaged. In order to screw in the Indexing Plungers, a screw-in washer can be supplied. The washer is slid beneath the disengaged mushroom knob so that the follower pins engage in the slot.

On request:
Special versions.

(Kipp Original Design)

Request Information

Unit of Measure

Items	M65625 Indexing Plunger - No Collar - Locking Bolt Not Hardened - Stainless Steel - Metric	M65609 Indexing Plunger - No Collar - Locking Bolt Not Hardened - Stainless Steel - Metric	M65613 Indexing Plunger - No Collar - Locking Bolt Not Hardened - Stainless Steel - Metric	M65615 Indexing Plunger - No Collar - Locking Bolt Not Hardened - Stainless Steel - Metric	M65617 Indexing Plunger - No Collar - Locking Bolt Not Hardened - Stainless Steel - Metric
Material	N/A Stainless Steel
Style	N/A G
L	N/A 31.50 mm	N/A 43.00 mm	N/A 50.00 mm	N/A 59.00 mm	N/A 77.00 mm
D	N/A 3.00 mm	N/A 4.00 mm	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm
H	N/A 3.50 mm	N/A 4.00 mm	N/A 5.00 mm	N/A 6.00 mm	N/A 8.00 mm
D2	N/A 14.00 mm	N/A 18.00 mm	N/A 21.00 mm	N/A 25.00 mm	N/A 33.00 mm
L2	N/A 11.00 mm	N/A 18.00 mm	N/A 21.00 mm	N/A 25.00 mm	N/A 33.00 mm
L1	N/A 17.00 mm	N/A 21.00 mm	N/A 24.00 mm	N/A 28.00 mm	N/A 36.00 mm
D1	N/A 1/4-28 in	N/A 5/16-24 in	N/A 3/8-24 in	N/A 1/2-13 in	N/A 5/8-11 in
F x 30°	N/A 0.80 mm	N/A 1.00 mm	N/A 1.30 mm	N/A 1.80 mm	N/A 2.30 mm
F1 - Spring Force Initial Pressure	N/A 4.5 N	N/A 6 N	N/A 5 N	N/A 6 N	N/A 15 N
F2 - Spring Force Final Pressure	N/A 9 N	N/A 12 N	N/A 12 N	N/A 14 N	N/A 35 N
SW	N/A
End Pressure Initial-Final	N/A