Print Back

Material:

  • Steel version, locking pin hardened: quality class 5.8
  • Stainless steel version, locking pin hardened: threaded sleeve 1.4305 locking pin 1.4034
  • Stainless steel version, locking pin not hardened: threaded sleeve 1.4305 locking pin 1.4305

    Mushroom knob in anthracite gray thermoplastic

    Surface finish:

  • Steel version, locking pin hardened: black oxide finish, locking pin ground - Stainless steel version, locking pin hardened: natural finish, locking pin ground
  • Stainless steel version, locking pin not hardened: natural finish, locking pin ground

    Note:
    Indexing Plungers are used to prevent any change in locking position due to lateral forces. A new locking position can only be set after the bolt has been manually disengaged. In order to screw in the Indexing Plungers, a screw-in washer can be supplied. The washer is slid beneath the disengaged mushroom knob so that the follower pins engage in the slot.

    On request:
    Special versions.

    (Kipp Original Design)
  • Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Unit of Measure
    Items Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    M65653
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    M65607
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    M65611
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    M65629
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    M65645
    Indexing Plunger - No Collar - Locking Bolt Hardened - Steel - Metric
    Material N/A Steel
    Style N/A G
    L N/A 31.50 mm N/A 43.00 mm N/A 50.00 mm N/A 59.00 mm N/A 77.00 mm
    D N/A 3.00 mm N/A 4.00 mm N/A 5.00 mm N/A 6.00 mm N/A 8.00 mm
    H N/A 3.50 mm N/A 4.00 mm N/A 5.00 mm N/A 6.00 mm N/A 8.00 mm
    D2 N/A 14.00 mm N/A 18.00 mm N/A 21.00 mm N/A 25.00 mm N/A 33.00 mm
    L2 N/A 11.00 mm N/A 18.00 mm N/A 21.00 mm N/A 25.00 mm N/A 33.00 mm
    L1 N/A 17.00 mm N/A 21.00 mm N/A 24.00 mm N/A 28.00 mm N/A 36.00 mm
    D1 N/A 1/4-28 in N/A 5/16-24 in N/A 3/8-24 in N/A 1/2-13 in N/A 5/8-11 in
    F x 30° N/A 0.80 mm N/A 1.00 mm N/A 1.30 mm N/A 1.80 mm N/A 2.30 mm
    F1 - Spring Force Initial Pressure N/A 4.5 N N/A 6 N N/A 5 N N/A 6 N N/A 15 N
    F2 - Spring Force Final Pressure N/A 9 N N/A 12 N N/A 12 N N/A 14 N N/A 35 N
    SW N/A
    End Pressure Initial-Final N/A